If your car will not start, there are several reasons that can cause this. Firstly your battery could be dead or discharged. To differentiate between a dead battery and a discharged battery, you need to crank the engine. If the headlights come on then dim severely, your battery has discharged. But if they do not come at all, your battery is dead. You may need to seek jump start services Buffalo NY to get you going.
Before you attempt to get your car jump started, you should inspect the battery connections to confirm they are okay. A poor connection could also be the reason why the engine does not start or the lights do not come on. If you are in a position, you should also check the battery voltage.
The best way to deal with a discharged battery is to recharge it with a battery charger instead of jump starting it. The modern vehicles have a lot of electronics installed. If you jump start a discharged battery, you may end up damaging your car. The voltage spike due to the jump start will damage the electrical components leaving you in a worse situation. You should also confirm the battery connections are okay before jump-starting. A loose connection can also cause similar damage.
Never attempt to jump-start a vehicle when it is freezing outside. The battery could be frozen as well. Jump-starting such a battery could cause it to explode. If your car is computer controlled, the best thing to do if your battery is dead is to remove it and charge it. Jump-starting is not advised. However, if you attempt to jump start, ensure the ignition is off on both vehicles as you make the connections. The two vehicles should also not be touching or they may provide an unwanted ground path.
Some vehicles provide special instructions to any jump-starting event. These instructions are provided for in the service information. You should have a look at this before you start. They can prevent you from causing damage to your vehicle. Always protect yourself from any injury by following all safety procedures.
The best jump start cables to use are those that are flexible, large in size and do not overheat. Braided copper cables are usually of good quality. Aluminum jump start cables are small and tend to overheat. They can easily burn you if you are not careful.
When jump starting, be cautious and wear protective gear especially for your eyes. Sparks may be created as you connect the cables and they can hurt your eyes. Be more cautious when connecting the last cable.
Ensure the cables are connected properly. There could be serious damage to the car's electrical system if the cables are connected backward. You should connect the hot cables first followed by the ground cables. Once the dead vehicle starts, the jumper cables should be disconnected immediately in reverse order of how they were installed.
Before you attempt to get your car jump started, you should inspect the battery connections to confirm they are okay. A poor connection could also be the reason why the engine does not start or the lights do not come on. If you are in a position, you should also check the battery voltage.
The best way to deal with a discharged battery is to recharge it with a battery charger instead of jump starting it. The modern vehicles have a lot of electronics installed. If you jump start a discharged battery, you may end up damaging your car. The voltage spike due to the jump start will damage the electrical components leaving you in a worse situation. You should also confirm the battery connections are okay before jump-starting. A loose connection can also cause similar damage.
Never attempt to jump-start a vehicle when it is freezing outside. The battery could be frozen as well. Jump-starting such a battery could cause it to explode. If your car is computer controlled, the best thing to do if your battery is dead is to remove it and charge it. Jump-starting is not advised. However, if you attempt to jump start, ensure the ignition is off on both vehicles as you make the connections. The two vehicles should also not be touching or they may provide an unwanted ground path.
Some vehicles provide special instructions to any jump-starting event. These instructions are provided for in the service information. You should have a look at this before you start. They can prevent you from causing damage to your vehicle. Always protect yourself from any injury by following all safety procedures.
The best jump start cables to use are those that are flexible, large in size and do not overheat. Braided copper cables are usually of good quality. Aluminum jump start cables are small and tend to overheat. They can easily burn you if you are not careful.
When jump starting, be cautious and wear protective gear especially for your eyes. Sparks may be created as you connect the cables and they can hurt your eyes. Be more cautious when connecting the last cable.
Ensure the cables are connected properly. There could be serious damage to the car's electrical system if the cables are connected backward. You should connect the hot cables first followed by the ground cables. Once the dead vehicle starts, the jumper cables should be disconnected immediately in reverse order of how they were installed.
About the Author:
You can get valuable tips on how to pick a towing company and more information about a reputable company that offers jump start services Buffalo NY area at http://www.towingbuffalo.com now.
No comments:
Post a Comment